Search found 29 matches

by mac74
Sun Sep 21, 2008 3:24 am
Forum: MegaSquirt Fuel Injection
Topic: Problem with air temp-sensor.
Replies: 1
Views: 3151

Re: Problem with air temp-sensor.

Problem solved! I had forgot to ground ljet-pin 6.
by mac74
Thu Sep 18, 2008 11:03 am
Forum: MegaSquirt Fuel Injection
Topic: Problem with air temp-sensor.
Replies: 1
Views: 3151

Problem with air temp-sensor.

Hi! I have my ms installed and is about to start tuning it. The problem I've encountered is that the MAT-gauge in megatune shows nada when engine is running. It lights up when I turn the key to mar-position but goes out when I crank and stays off when engine runs. Tried a different sensor just to ru...
by mac74
Thu Jul 31, 2008 10:44 am
Forum: MegaSquirt Fuel Injection
Topic: Wanted, 3.0 12V msq
Replies: 2
Views: 3304

Wanted, 3.0 12V msq

Does anyone have a .msq for the 3.0 12V. Fuel-only. I just want something to start off with.

I tried to open Steve R's .msq from the download section but that doesn't work. Guess because of some version differences.

I run MT 2.25p3 with MsExtra 029y4.

/Marcus
by mac74
Tue Jul 29, 2008 12:37 am
Forum: MegaSquirt Fuel Injection
Topic: Bosch IAT and CLT sensor values?
Replies: 2
Views: 3623

Thanks, Murray! I'm going for a first startup-attempt later today :)
by mac74
Mon Jul 28, 2008 12:26 pm
Forum: MegaSquirt Fuel Injection
Topic: Bosch IAT and CLT sensor values?
Replies: 2
Views: 3623

Bosch IAT and CLT sensor values?

Does anyone have the correct temp/ohm values for use with Easytherm? Sensors are stock Bosch.

/Marcus
by mac74
Mon Jul 14, 2008 1:34 pm
Forum: MegaSquirt Fuel Injection
Topic: Installing MS 3.57
Replies: 10
Views: 8806

I'm going for fuel-only to start with before doing ignition. With my MS1 I think it's db37-pin36 that is to be connected directly to the ignition module. Don't know about f-idle.
by mac74
Mon Jul 14, 2008 12:40 am
Forum: MegaSquirt Fuel Injection
Topic: Installing MS 3.57
Replies: 10
Views: 8806

I'm sure you'll figure it out. If you check the backside of the ljet-connector you'll notice that every pin is numbered. You don't have to worry about the MS-pins since you have the pigtail with labeled wires, right? If you use the excel-document you'll only have to match for example, the CLT (coola...
by mac74
Sun Jul 13, 2008 10:52 am
Forum: MegaSquirt Fuel Injection
Topic: Installing MS 3.57
Replies: 10
Views: 8806

Hmmm, don't know why uploading the .pdf doesn't work!? Paul, If you want that too I can email it to you.
by mac74
Sun Jul 13, 2008 10:49 am
Forum: MegaSquirt Fuel Injection
Topic: Installing MS 3.57
Replies: 10
Views: 8806

Yes, I have. Here they are.
by mac74
Tue Jul 08, 2008 10:42 am
Forum: MegaSquirt Fuel Injection
Topic: Installing MS 3.57
Replies: 10
Views: 8806

Paul, It's not that much to see really, but I recommend you to slaughter an ljet-box to build the adaptor and also to get the db37-pigtail. As you can see there's still a few wires to be soldered. Hopefully I will just plug in the MS and start tuning soon ;)

Here goes:
by mac74
Tue Jul 08, 2008 1:12 am
Forum: MegaSquirt Fuel Injection
Topic: Installing MS 3.57
Replies: 10
Views: 8806

Installing MS 3.57

Hi! I'm just finishing my install using a pre-built MS1 3.57. I've followed the MS > L-Jet drawing when building the adaptor for using my existing LJet-harness. I also bought a db37-pigtail to make life easier. I have two groundcables coming from the db37-pigtail. I just ground them to the Ljet-casi...
by mac74
Wed Mar 19, 2008 4:12 am
Forum: Performance
Topic: CB S1 Cams
Replies: 5
Views: 2294

Yeah, Killaz, I have seen those figures. But since I don't know for sure that my S1-cams are identical to the stradale medio's i thought I'd ask here. I was thinking that someone might have some older list from CB with S1,S2 etc.
by mac74
Wed Mar 19, 2008 12:32 am
Forum: Performance
Topic: CB S1 Cams
Replies: 5
Views: 2294

Zamani, your right about this being an old grind. However, It seems that these could match with todays 'stradale medio' considering the 10.4 lift. I mailed C&B and asking for specs but they seem to be having a hard time to get back to me. When is the limit reached concerning retainer/seal-contact or...
by mac74
Tue Mar 18, 2008 1:35 pm
Forum: Performance
Topic: CB S1 Cams
Replies: 5
Views: 2294

CB S1 Cams

Hi!

I've come about a set of Colombo & Bariani S1 camshafts. These are meant to go inside my 3.0 12V.

I'm not 100% sure but I think they have a lift of 10.4mm. Do these go in my 3.0 heads without modifications to the valveguides etc?

If someone have the specs for these cams it would be great.
by mac74
Tue Jul 10, 2007 1:27 pm
Forum: Fuel, Electrical & ignition (stock Bosch)
Topic: ECU from BMW 528?
Replies: 5
Views: 2450

I'm running a BMW 635 Ecu and BMW 528 AFM in my GTV6 3.0 It's plug and play hardwarewise. The connectors are the same. I had to adjust the AFM springload quite a bit though to get rid of some low-rpm stutter. Now it runs really good, but I'm still unsure if air/fuel mixture is correct in low rpm's. ...